Smart Storage Administrator Diagnostics and SmartSSD Wear Gauge Utility CLI Version 2.60-18.0 8/31/2016 Description ----------- Smart Storage Administrator Diagnostics and SmartSSD Wear Gauge Utility CLI (SSADUCLI) is a command line application that creates a report of all HPE Storage controllers and disk drives. This report provides vital information to HPE service personnel to assist in identifying faults or conditions that may require attention. The utility can also generate SmartSSD Wear Gauge reports. These reports contain wear (usage) information for all SmartSSD devices attached to the system. * All other product names mentioned herein may be trademarks of their respective companies. Supported Operating Systems and Platforms ----------------------------------------- Linux 32-bit components: SuSE Linux Enterprise Server 10 SuSE Linux Enterprise Server 11 Red Hat Enterprise Linux 5 Red Hat Enterprise Linux 6 Red Hat Enterprise Linux 7 Linux 64-bit components: SuSE Linux Enterprise Server 10 (x86_64) SuSE Linux Enterprise Server 11 (x86_64) Red Hat Enterprise Linux 5 (x86_64) Red Hat Enterprise Linux 6 (x86_64) Red Hat Enterprise Linux 7 (x86_64) Debian Sarge 64 bit Debian Etch (amd64) NOTE: For Red Hat Enterprise Linux 7.1 the sg driver must be manually added so that it is loaded at boot time. Without the sg driver being loaded, devices or controllers may not be discovered. Here is a recommended way to do this: sudo echo sg > /etc/modules-load.d/sg.conf sudo rebo * Any platform that requires the CCISS driver should use version 3.6.28 or newer. These drivers are available from http://support.hpe.com. Supported Controllers --------------------- Dynamic Smart Array B110i SATA RAID Smart Array P212 Controller Smart Array P410 Controller Smart Array P410i Controller Smart Array P411 Controller Smart Array P711m Controller Smart Array P712m Controller Smart Array P812 Controller Dynamic Smart Array B120i Dynamic Smart Array B320i Smart Array P220i Controller Smart Array P222 Controller Smart Array P420 Controller Smart Array P420i Controller Smart Array P421 Controller Smart Array P721m Controller Smart Array P822 Controller Smart Array P230i Controller Smart Array P430 Controller Smart Array P431 Controller Smart Array P530 Controller Smart Array P531 Controller Smart Array P731m Controller Smart Array P830 Controller Smart Array P830i Controller Dynamic Smart Array B140i Smart HBA H240 Controller Smart HBA H240ar Controller Smart HBA H240nr Controller Smart HBA H241 Controller Smart HBA H244br Controller Smart Array P240nr Controller Smart Array P244br Controller Smart Array P246br Controller Smart Array P440 Controller Smart Array P440ar Controller Smart Array P441 Controller Smart Array P542D Controller Smart Array P741m Controller Smart Array P840 Controller Smart Array P840ar Controller Smart Array P841 Controller Installing and running Smart Storage Administrator -------------------------------------------------------------- Installation: SSADUCLI is distributed using Red Hat Package Manager (RPM) packages. If there is an older version of SSADUCLI installed on the system, please use "rpm -e ssaducli" to remove it first. Use "rpm -i " to install the application. Please type "man rpm" for other details regarding RPM. The software resides in /opt/smartstorageadmin/ssaducli and the executable name is ssaducli which is located in /usr/sbin. When attempting to run SSADUCLI on any HPE-supported version of Linux, it is highly recommended that you install the latest version of the HPE ProLiant Smart RAID/HBA controller driver for your intended Linux operating system. Drivers may be obtained by clicking on "HPE Servers, Storage and Networking" from HPE's support website at: http://support.hpe.com To run the command-line application: Open a command prompt and change directory (cd) to the location where SSADUCLI is installed. This is commonly /opt/smartstorageadmin/ssaducli/bin. To generate a diagnostic report, enter the following command: ssaducli -f adu-report.zip To generate a SmartSSD Wear gauge report, enter the following command: ssaducli -ssd -f ssd-report.zip More options can be found by "ssaducli -help". Additional Notes ---------------- Both the diagnostic and SmartSSD wear gauge reports are generated in compressed (ZIP) format. The diagnostic report output archive contains the following files: * ADUReport.txt => Diagnostic report in text format * ADUReport.xml => Diagnostic report in XML format * ADUReport.htm => HTML viewer for diagnostic report * report.checksum => checksum file * SlotX.txt (SlotX.old) => Controller serial output log Note: The serial output log file(s) are only available if the "HPE Storage Agent" daemon is installed and running. To view the diagnostic report in a browser, extract the ADUReport.htm. Open ADUReport.htm in the browser. The SmartSSD wear gauge report output archive contains the following files: * SmartSSDWearGaugeReport.txt => SmartSSD wear gauge report in text format * SmartSSDWearGaugeReport.js => SmartSSD wear gauge report in JSON format * SmartSSDWearGaugeReport.htm => HTML viewer for the JSON wear gauge report To view the SmartSSD wear gauge report in a browser, extract the SmartSSDWearGaugeReport.js, SmartSSDWearGaugeReport.htm files to a directory (both files must reside in the same directory). Open SmartSSDWearGaugeReport.htm in the browser. Support ------- For support for SSADUCLI and Smart RAID/HBA controllers, please visit http://support.hpe.com.