#cd hpiefplManagementCD-3.00
# ./install.sh
Welcome to the HP Enablement Kit for Linux supplemental CD version 3.00.
Check http://downloads.hpe.com/pub/linux for software updates [Y/n]?
n ←”n”を入力し、HPEサイトからのアップデートを無効に
You have selected not to update your Supplemental CD software at this time. If
you would like to
update this software in the future, you can obtain the latest version from HP's
support website as
follows:
1. Browse to http://www.hp.com/go/support.
2. Search for software based on your server type (for example: rx2620, rx7620
or Superdome).
3. Browse to the software and drivers download page for your operating system.
Press <enter> to continue the installation of the current version of
the Supplemental CD.
←Enterキー入力
installing hpmgmtbase-1.9-6.rhel4.ia64.rpm
Please wait while data is cached...
Start HP IPMI SEL daemon 'hpseld': [ OK ]
The hpmgmtbase RPM has installed successfully.
1. Install HP Insight Manager Agents for IA-64 Linux
2. Install HP System Management Homepage for Linux on the Itanium Processor
3. Install nPartition Commands
4. Install The nPartition Management GUI for HP Integrity servers.
5. Install WBEM providers for Integrity servers
6. Install HP Command Line Array Configuration Utility
7. Install everything and exit
8. Exit
What do you want to install?
1 ←”1”を入力し、HPIMAをインストール
Removing net-snmp-perl
Removing net-snmp-devel
Removing net-snmp-utils
Removing net-snmp
Removing net-snmp-libs
compat-libstdc++-296-2.96-132.7.2 is up to date.
installing net-snmp-libs-5.1.2-11.EL4.6hp.ia64.rpm
installing net-snmp-5.1.2-11.EL4.6hp.ia64.rpm
installing net-snmp-utils-5.1.2-11.EL4.6hp.ia64.rpm
installing net-snmp-devel-5.1.2-11.EL4.6hp.ia64.rpm
installing net-snmp-perl-5.1.2-11.EL4.6hp.ia64.rpm
installing hpima-2.5-5.rhel4.ia64.rpm
Enabling snmpd at runlevel 2.
Enabling snmpd at runlevel 3.
Enabling snmpd at runlevel 4.
Enabling snmpd at runlevel 5.
__________________________________________________________________________
The following file(s) contain the current SNMP configuration:
/etc/snmp/snmpd.conf
Please respond to the following prompts to configure
SNMP for use with HP Insight Management Agents...
snmp設定...
__________________________________________________________________________
Configuring SNMP general information...
The system contact is set to
"Root <root@localhost> (configure /etc/snmp/snmp.local.conf)"
Do you wish to change it (y/n) (Blank is n):
The system location is set to
"Unknown (edit /etc/snmp/snmpd.conf)"
Do you wish to change it (y/n) (Blank is n):
local community設定...
__________________________________________________________________________
Configuring SNMP access from 'localhost'
Enter 'Read Only' community string (one word, Blank to skip): ←community名を入力
Re-enter the same input to confirm: ←community名を再入力
Enter 'Read/Write' community string (one word, required, no default): ←community名を入力
Re-enter the same input to confirm: ←community名を再入力
remote community設定...
__________________________________________________________________________
Configuring SNMP access from remote Management Station(s)
Enter 'Read Only' IP or DNS name (blank to skip): 192.168.0.11 ←IP/Host名を入力
Enter 'Read Only' community string to be used by "192.168.0.11"
(one word, required, no default): ←community名を入力
Re-enter the same input to confirm: ←community名を再入力
Enter 'Read Only' IP or DNS name (blank to skip):
Enter 'Read/Write' IP or DNS name (blank to skip): 192.168.0.11
Enter 'Read/Write' community string to be used by "192.168.0.11"
←IP/Host名を入力
(one word, required, no default): ←community名を入力
Re-enter the same input to confirm: ←community名を再入力
Enter 'Read/Write' IP or DNS name (blank to skip):
snmp trap設定...
__________________________________________________________________________
Configuring SNMP TRAPs sent from this system......
Enter default trap community string (blank to skip): public ←community名を入力
Enter SNMP trap destination IP or DNS name (blank to quit): 192.168.0.11 ←IP/Host名を入力
Enter trap community string for trap destination "192.168.0.11"
(One word; Blank is ok): public ←community名を入力
Enter SNMP trap destination IP or DNS name (blank to quit):
__________________________________________________________________________
The following file(s) contained the prior SNMP configuration:
/etc/snmp/snmpd.conf
They have been saved and will be restored when hpima is removed.
New configuration is saved in /etc/snmp/snmpd.conf.
Run '/etc/init.d/hpima reconfigure' to make changes.
__________________________________________________________________________
(Re)starting the SNMP daemon, configured to support the
HP Insight Management Agents
ln: `/usr/lib/libqlsdm.so': File exists
Start SNMP AgentX Intermediary 'hpimaX': [ OK ]
Start Foundation Peer Daemon 'hpimafdtnpeerd': [ OK ]
Start Foundation Host Agent 'hpimahostd': [ OK ]
Start Foundation Threshold Agent 'hpimathreshd': [ OK ]
Start Server Peer Daemon 'hpimasvrpeerd': [ OK ]
Start Server Health Agent 'hpimahealthd': [ OK ]
Start Server Standard Equipment Agent 'hpimastdeqd': [ OK ]
Start Storage Peer Daemon 'hpimastorpeerd': [ OK ]
Start Storage Event Agent 'hpimaeventd': [ OK ]
Start Storage Intelligent Disk Array Agent 'hpimaidad': [ OK ]
Start Storage SCSI Agent 'hpimascsid': [ OK ]
Start Storage Fibre Channel Agent 'hpimafcad': [ OK ]
Start NIC Peer Daemon 'hpimanicpeerd': [ OK ]
Start NIC Agent 'hpimanicd': [ OK ]
Start Event E0 Trap Generator 'hpimaE0traps': [ OK ]
HP Insight Management Agents are enabled
The hpima RPM has installed successfully.
1. Install HP Insight Manager Agents for IA-64 Linux
2. Install HP System Management Homepage for Linux on the Itanium Processor
3. Install nPartition Commands
4. Install The nPartition Management GUI for HP Integrity servers.
5. Install WBEM providers for Integrity servers
6. Install HP Command Line Array Configuration Utility
7. Install everything and exit
8. Exit
What do you want to install?
8 ←”8"を入力し、インストールシェルを終了
exiting . . .
|