SOFTPAQ NUMBER: N/A PART NUMBER: N/A FILE NAME: adpahci.v1.19.V414A19.V041A7.rhel3qu4.x86_64.img TITLE: HP Embedded SATA RAID Controller Driver Diskette for Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) VERSION: v1.19.V414A19.V041A7 KEY FILE: LANGUAGE: English CATEGORY: Driver - Storage Controller DIVISION: N/A OPERATING SYSTEM: Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) PREREQUISITES: N/A EFFECTIVE DATE: 08/26/2005 ELECTRONIC DISTRIBUTION ALLOWED: YES SOFTPAQ UTILITY VERSION: N/A SUPERSEDES: N/A SUPPORT SYSTEMS/DEVICES: ProLiant ML110 G3 HP Embedded SATA RAID Controller DESCRIPTION: ~~~~~~~~~~~~ This driver diskette image provides the binary driver modules pre-built for Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) to enable the HP Embedded SATA RAID Controller. Using a driver diskette at Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) installation time allows the most up-to-date driver version included in the diskette to be used, rather than the default driver version contained in the Linux Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) installation CD. FIXES: ~~~~~~ KNOWN ISSUES: ~~~~~~~~~~~~~ ENHANCEMENTS: ~~~~~~~~~~~~~ CREATING A DRIVER DISKETTE -------------------------- There are two methods to create the Installation Diskette: MAKING A DISKETTE UNDER MS-DOS: ------------------------------- 1) Save the "[package name]" file into a temporary directory. 2) Use the "rawrite" utility which is included on the Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) CD. 3) Label a blank, formatted 3.5-inch diskette as "HP Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) Driver Diskette". Next, insert the diskette in the diskette drive. Then, use the following commands (assuming your Disk Image is at the location c: and your CD-ROM is drive d:) C:\> d:\dosutils\rawrite Enter disk image source file name: adpahci.v1.19.V414A19.V041A7.rhel3qu4.x86_64.img Enter target diskette drive: a: Please insert a formatted diskette into drive A: and press --ENTER-- : Enter MAKING A DISKETTE UNDER A LINUX-LIKE OS: ---------------------------------------- 1) Save the "adpahci.v1.19.V414A19.V041A7.rhel3qu4.x86_64.img" file into a temporary directory. 2) To make a diskette under Linux (or any other Linux-like operating system), you must have permission to write to the device representing a 3.5-inch diskette drive (known as /dev/fd0 under Linux) 3) First, label a blank, formatted diskette appropriately (HP Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) Driver Diskette). Insert the diskette into the floppy drive, but DO NOT issue the mount command: # dd if=adpahci.v1.19.V414A19.V041A7.rhel3qu4.x86_64.img of=/dev/fd0 bs=1440k 4) This command creates a diskette containing the image of the input file (adpahci.v1.19.V414A19.V041A7.rhel3qu4.x86_64.img) to an output file (of=/dev/fd0) using the diskette size of 1440k (1.44MB). To make another diskette label that diskette, and run "dd" again, specifying the correct input file. INSTALLATION ------------ To install Linux using this "HP Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) Driver Diskette", boot your Linux machine with your Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) CD1 in your CD-ROM Drive. A menu will be displayed, prompting for your input. Type the following line of code to inform the operating system of the diskette: # linux updates dd Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) will prompt for the Updates Diskette and the HP Red Hat Enterprise Linux 3 Update 4 (AMD64/EM64T) Driver Diskette during the installation procedure. Customer Service --------------------------------------------------- For support, please send email to contact.hp@hp.com Copyright 2005, Hewlett_Packard Development Company, L.P. Product names mentioned heren may be trademarks and/or registered trademarks of their respective companies.