FILE NAME: bcm5700-6.0.2d-1.src.rpm TITLE: HP Tested and Approved bcm5700 Linux NIC Driver VERSION: 6.0.2d LANGUAGE: English CATEGORY: Software Solutions DIVISIONS: Enterprise and Mainstream Servers PRODUCTS AFFECTED: HP NC6770 Gigabit Server Adapter HP NC7760 Gigabit Server Adapter HP NC7770 Gigabit Server Adapter HP NC7780 Gigabit Server Adapter HP NC7781 Gigabit Server Adapter OPERATING SYSTEM: Red Hat Linux 8.0 Professional - Errata kernel 2.4.18-27 (SMP,UP and BigMem) Red Hat Linux 7.3 Professional - Errata kernel 2.4.18-27 (SMP,UP and BigMem) Red Hat Linux 7.2 Professional - Errata kernel 2.4.18-27 (SMP and UP) Red Hat Enterprise Linux AS 2.1 - Errata kernel 2.4.9-e.16 (SMP,UP and Enterprise) Red Hat Enterprise Linux ES 2.1 - Errata kernel 2.4.9-e.16 (SMP,UP and Enterprise) SuSE Linux Enterprise Server 7 (SLES-7) - Errata kernel 2.4.18-244 (SMP) - Errata kernel 2.4.18-262 (UP) Conectiva Linux Enterprise Edition, SCO Linux 4.0, SuSE Linux Enterprise Server 8 and Turbolinux 8 all powered by UnitedLinux 1.0. - Service Pack 2 (service packs must be installed in order, from service pack 1 to the above service pack) Note: Currently, the BigMem Errata Kernel 2.4.18-27 is not supported on Red Hat Linux 7.2 Professional due to some driver installation issues. PREREQUISITES: Pentium based computer 128MB RAM minimum Latest HP System ROM Note: Please visit the following URL to upgrade the ROM http://h18000.www1.hp.com/support/files EFFECTIVE DATE: 06/05/2003 SUPERSEDES: bcm5700-6.0.2a-1.src.rpm DESCRIPTION: This RPM Package contains the HP Tested and Approved bcm5700 Linux NIC Driver for use with the Server Adapters mentioned in the PRODUCTS AFFECTED section of this document. ENHANCEMENTS/FIXES: Packaging enhancements to handle UL Service Pack Updates Table of Contents ================= Introduction Packaging Kernel Source Code Setup Installing the RPM Package Module Parameters Driver Messages Statistics Limitations Introduction ============ This file describes the Linux driver for the HP Gigabit Server Adapters mentioned in the PRODUCTS AFFECTED section of this document. After installation, additional information can be found in the manual page for bcm5700, and in the RELEASE.TXT file located at: For Red Hat: /usr/share/doc/bcm5700-/RELEASE.TXT For SuSE SLES7: /usr/share/doc/packages/bcm5700/RELEASE.TXT For UnitedLinux 1.0: /usr/share/doc/packages/bcm5700/RELEASE.TXT User guides and additional HP Network Adapter information can be found at: http://h18000.www1.hp.com/support/networking/nics/index.html Packaging ========= The driver is released in a source RPM format. The file name for the package is bcm5700-.src.rpm and is dependent on the kernel source code. If you have not installed the kernel source code and/or setup the source tree on your Linux system, please see the "Kernel Source Code Setup" section below. Kernel Source Code Setup ======================== The bcm5700 driver requires the presence of the kernel source code and configuring the kernel source before building the bcm5700 driver. The following steps need to be done once for each kernel that is booted. For example, if the current kernel is UP (uni-processor) and an SMP (symmetrical-multi-processor) kernel is booted, these steps must be performed again to configure the kernel source for SMP before building the bcm5700 driver for the SMP kernel. Red Hat installation: If the /usr/src/linux- directory does not exist install the kernel source code per Red Hat instructions. Once installed, follow the commands listed below to configure the kernel source to match the running kernel. # cd /usr/src/linux- # make mrproper # make -e KERNELRELEASE=`uname -r` oldconfig # make -e KERNELRELEASE=`uname -r` dep SuSE SLES 7 and UnitedLinux 1.0 Installations: If the /usr/src/linux- directory does not exist please install the kernel source code per SuSE instructions. Once installed, please follow the commands listed below to setup the kernel source tree. # cd /usr/src/linux-.SuSE # cp /boot/vmlinuz.config .config # cp /boot/vmlinuz.version.h include/linux/version.h # cp /boot/vmlinuz.autoconf.h include/linux/autoconf.h # make oldconfig # make dep Installing the RPM Package ============================= 1. This package requires the kernel source code as well as setting up the source tree. Verify the source code /usr/src/linux- directory exist. # cd /usr/src/linux- If the kernel source code is not present, then please refer to the "Kernel Source Code Setup" section. 2. Install the source RPM package. # rpm -ivh bcm5700-.src.rpm 3. Build the binary RPM for the bcm5700 driver. Red Hat Installation: # cd /usr/src/redhat # rpmbuild -bb SPECS/bcm5700.spec SuSE SLES 7 and UnitedLinux 1.0 Installations: # cd /usr/src/packages # rpm -bb SPECS/bcm5700.spec If you get an error during the build process, please refer to the "Kernel Source Code Setup" section to correctly setup the source tree. 4. Check for the existence of a current version of the bcm5700 package as follows: # rpm -q bcm5700 If an old version of the package exists the RPM package should be removed. # rpm -e bcm5700 Then remove the loaded bcm5700 module. # rmmod bcm5700 Verify that the old bcm5700 package has been removed as follows: # rpm -q bcm5700 5. Install the new RPM package. This installs the bcm5700 driver and man page. Don't use the U (Upgrade) flag in the RPM command below - previous bcm5700 drivers must be removed as described in step 4 above before installing this version. # rpm -ivh RPMS/i386/bcm5700-.i386.rpm --force The bcm5700.o module is installed in the following directory: Red Hat 8.0 /lib/modules//kernel/drivers/net Red Hat 7.3 /lib/modules//kernel/drivers/net Red Hat 7.2 /lib/modules//kernel/drivers/net Red Hat AS 2.1 /lib/modules//kernel/drivers/addon/bcm5700 Red Hat ES 2.1 /lib/modules//kernel/drivers/addon/bcm5700 SuSE SLES 7 /lib/modules//kernel/drivers/net/bcm UnitedLinux 1.0 /lib/modules//kernel/drivers/net/bcm 5. Configure your network setting and address. You may need to refer to your Linux vendor documentation. Use the "netconfig" tool for RedHat configuration. Other helpful network configuration tools such a "yast" in SLES 7 and UnitedLinux exist for easy configuration. 6. Ensure that the /etc/modules.conf file is configured similar to the example listed below. The example below is presented as if more than one adapter is present. If so, one eth# instance should exist for each ethernet port. View the modules.conf man page for more information. alias eth0 bcm5700 alias eth1 bcm5700 alias eth# bcm5700 7. You can now reboot your server. Upon reboot the network should start with the bcm5700 driver loaded and the correct network configuration. To verify that the bcm5700 driver is loaded, use the following command. # lsmod If bcm5700 is listed then the bcm5700 driver loaded. Note: By default Red Hat 8.0 installs the tg3 driver. If the tg3 driver is installed, please unload the tg3 driver first. Use ifconfig to bring down all eth# interfaces used by tg3. # ifconfig eth# down Now remove or unload the tg3 driver. # rmmod tg3 You may also need to manually edit the /etc/modules.conf file to change the driver from tg3 to bcm5700. alias eth0 tg3 and replace tg3 with bcm5700: alias eth0 bcm5700 Load the bcm5700 driver: # insmod bcm5700 Use ifconfig to bring up the network with the new driver: # ifconfig eth# up See the man pages for lsmod, ifconfig, rmmod, insmod and modules.conf for more detailed information. Module Parameters ================= The complete set of Module Parameters supported by the bcm5700 driver is described in the RELEASE.TXT which is installed under the appropriated directories as mentioned in the Introduction section. Special Note on the "mtu" parameter: Enables jumbo frames if MTU is set equal to or greater than 1501. The valid range for MTU is from 1500 to 9000. Default is standard MTU size, 1500 (not a jumbo frame). Note: MTU size excludes the Ethernet header size of 14 bytes. Actual frame size is MTU size + 14 bytes. Special Note on the "rx_jumbo_desc_cnt" parameter: It is always advised to use a value of 15 or above for the module parameter rx_jumbo_desc_cnt. At values lower than 15, it has been observed that jumbo traffic causes the driver to hang. Driver Messages =============== The following are the most common sample messages that may be logged in the file /var/log/messages. Some Linux distributions may not display messages to the console. To set messages to display on the console, at the command line use to control the level at which messages will appear on the console. # dmesg -n 6 Most systems are set to level 6 by default. For Example, if a HP NC7771 Gigabit Server Adapter is installed, the set of messages would look as follows: eth#: HP NC7771 Gigabit Server Adapter found at mem c6ff0000, IRQ 5, node addr 00101804088e eth#: Broadcom BCM5703 Integrated Copper transceiver found eth#: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON If a HP NC6770 Gigabit Server Adapter is installed, the set of messages would look as follows: eth#: HP NC6770 Gigabit Server Adapter found at mem c6fe0000, IRQ 10, node addr 000802280026 eth#: Agilent HDMP-1636 SerDes transceiver found eth#: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON Link up and speed indication bcm5700: eth# NIC Link is Up, 1000 Mbps full duplex Link down indication bcm5700: eth# NIC Link is Down Statistics ========== Detailed statistics and configuration information can be viewed by: # more /proc/net/nicinfo/eth#.info. Limitations =========== The /proc/net/nicinfo/eth#.info file may report incorrect information regarding statistics, and PCI slot. Please note that in some cases more tx_packets and/or rx_packets are reported than tx_bytes and/or rx_bytes, respectively. The reason for the error is due to counters rolling over. Also note that "PCI_SLOT" is not the actual physical slot. "PCI_SLOT" represents the PCI device ID. Under lower speed and half duplex combinations, a higher error count may be generated. This error will have minimal effect on the overall system and session performance. Some error count generation is a normal and expected occurrence in these conditions. Uninstalling the RPM ==================== The following command will uninstall the bcm5700 RPM. # rpm -e bcm5700- Copyright 2002, 2003 Hewlett-Packard Development Company, L.P. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies