SOFTPAQ NUMBER: N/A PART NUMBER: N/A FILE NAME: aic7xxx-6.3.11-5.rhel3.i686.dd.gz TITLE: Driver diskette for 64-Bit/66-Mhz Dual Channel Wide Ultra3 SCSI Controller (x86) for Red Hat Enterprise Linux 3 (x86) VERSION: 6.3.11-5 LANGUAGE: English CATEGORY: Driver Diskettes DIVISION: N/A OPERATING SYSTEM: Red Hat Enterprise Linux 3 EFFECTIVE DATE: May 5,2006 ELECTRONIC DISTRIBUTION ALLOWED: Yes SOFTPAQ UTILITY VERSION: N/A SUPERSEDES: N/A DESCRIPTION: This driver diskette image provides the binary driver module pre-built for Red Hat Enterprise Linux 3.0 to enable the HP Prolaint 64-Bit/66-Mhz Dual Channel Wide Ultra3 SCSI Controller. Using this driver diskette at Red Hat Enterprise Linux 3.0 installation time allows the most up-to-date driver version included in the diskette to be used, rather than the default driver version contained in the Red Hat Enterprise Linux 3.0 installation CD. FIXES ENHANCEMENTS The kernels of Red Hat Enterprise Linux 3 supported by this driver diskette are: 2.4.21-20.EL - Red Hat Enterprise Linux 3.0 Update 3 (x86) 2.4.21-27.EL - Red Hat Enterprise Linux 3.0 Update 4 (x86) 2.4.21-32.EL - Red Hat Enterprise Linux 3.0 Update 5 (x86) 2.4.21-37.EL - Red Hat Enterprise Linux 3.0 Update 6 (x86) 2.4.21-40.EL - Red Hat Enterprise Linux 3.0 Update 7 (x86) INSTALLATION To install Linux using this "ProLiant Red Hat Enterprise Linux 3.0" Driver Diskette, boot your Linux machine with your Red Hat Enterprise Linux 3.0 CD1 in your CD-ROM Drive. A menu will be displayed, prompting for your input. Type the following line of code to inform the operating system of the diskette: # linux dd Red Hat Enterprise Linux 3.0 will prompt for the Updates Diskette and the ProLiant Red Hat Enterprise Linux 3.0 Driver Diskette during the installation procedure. NOTES CREATING A DRIVER DISKETTE There are two methods to create the Installation Diskette: MAKING A DISKETTE UNDER MS-DOS: 1) Save the "aic7xxx-6.3.11-5.rhel3.i686.dd.gz" file into a temporary directory. Use WINZIP to extract "aic7xxx-6.3.11-5.rhel3.i686.dd" from this file into the same directory. Please ensure that "aic7xxx-6.3.11-5.rhel3.i686.dd" is a DOS 8.3 name. 2) Use the "rawrite" utility which is included on the Red Hat Enterprise Linux 3.0 CD in the "dosutil" directory. 3) Label a blank, formatted 3.5-inch diskette as "ProLiant Red Hat Enterprise Linux 3.0 Driver Diskette". Next, insert the diskette in the diskette drive. Then, use the following commands (assuming your ProLiant Disk Image is at the location c: and your CD-ROM is drive d:) C:\> d:\dosutils\rawrite Enter disk image source file name: aic7xxx-6.3.11-5.rhel3.i686.dd Enter target diskette drive: a: Please insert a formatted diskette into drive A: and press --ENTER-- : Enter MAKING A DISKETTE UNDER A LINUX-LIKE OS: 1) Save the "aic7xxx-6.3.11-5.rhel3.i686.dd.gz" file into a temporary directory. Use GUNZIP to extract "aic7xxx-6.3.11-5.rhel3.i686.dd" from this file into the same directory 2) To make a diskette under Linux (or any other Linux-like operating system), you must have permission to write to the device representing a 3.5-inch diskette drive (known as /dev/fd0 under Linux) 3) First, label a blank, formatted diskette appropriately (ProLiant Red Hat Enterprise Linux 3.0 Driver Diskette). Insert the diskette into the floppy drive, but DO NOT issue the mount command: # dd if=aic7xxx-6.3.11-5.rhel3.i686.dd of=/dev/fd0 bs=1440k 4) This command creates a diskette containing the image of the input file (if=aic7xxx-6.3.11-5.rhel3.i686.dd) to an output file (of=/dev/fd0) using the diskette size of 1440k (1.44MB). To make another diskette label that diskette, and run "dd" again, specifying the correct input file. MD5SUM: cdb03c72f0a88605abe00f04a146522b Customer Service ---------------- For support, please send email to contact.hp@hp.com. Copyright 2002, 2003 Hewlett-Packard Development Company, L.P. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.